Whether a material conducts, insulates, or holds a charge is a material's property, and it decides how a component performs and where it fails. Electrical Testing measures resistivity, dielectric behavior, insulation resistance, and breakdown across conductors, insulators, and semiconductors.
Whether a material conducts, insulates, or holds a charge is a material's property, and it decides how a component performs and where it fails. Electrical testing measures resistivity, dielectric behavior, insulation resistance, and breakdown across conductors, insulators, and semiconductors. MatX Lab measures these properties to verify a material, characterize an insulator or dielectric, qualify a coating, or find why a device shorted or leaked. The work quantifies how a material behaves under voltage and current.
In this, it is measured how a material responds to voltage and current. Also, resistivity and conductivity describe how easily charge moves, dielectric properties describe how an insulator stores and dissipates energy, and breakdown testing finds the voltage at which an insulator fails. These methods span thin films and wafers, bulk plastics and elastomers, ceramics, and coatings, wherever electrical behavior is a design requirement.
Electrical work depends on the material and the property, and we scope the right method. Each technique below links to its own page.
Measures volume and surface resistivity of materials from conductors to insulators, characterizing how readily charge moves through the bulk and along the surface.
Measures the sheet resistance of thin films and the resistivity of wafers, a core semiconductor and thin-film measurement.
Measures dielectric constant and dissipation factor across frequency, the properties that govern capacitance and insulation performance.
Determines the voltage at which an insulator breaks down, per thickness, for insulation qualification.
Measures resistance across an insulating material or coating under applied voltage, a routine check of insulating quality.
It ranks polymers and coatings from static-dissipative to fully insulating, important for electronics and ESD control.
Here we measure contact and interconnect resistance in assemblies, relevant to joints, connectors, and platings.
Electrical testing is the right method whenever conduction, insulation, or dielectric behavior is a requirement.
Electrical testing applies wherever materials carry, block, or store electrical energy.
Materials: Thin Films & Coatings · Wafers & Die · Plastics · Elastomers & Rubber · Ceramics & Glass
Industries: Electronics · Semiconductors · Energy · Manufacturing · Automotive
This process of electrical testing is method-driven, and your specification usually names the standard. Where an applicable standard exists, testing is aligned to it and cited in your report. We align to the method your specification requires and document it.
| Analysis / Standard | What It Covers |
|---|---|
| Ebic | Electron Beam Induced Current |
| Tlp | Transmission Line Pulse |
| Dhem | Differential Hall Effect Metrology |
| TDR | Time Domain Reflectometry |
| ASTM F672 | Silicon Wafer Resistivity Profiling by Spreading Resistance Probe |
| ASTM E598 | Extreme Heat-Transfer Rates from High-Energy Environments |
| ASTM E434 | Calorimetric Determination of Hemispherical Emittance and the Ratio of |
| ASTM D6744 | Thermal Conductivity of Anode Carbons |
| ASTM E128 | Maximum Pore Diameter and Permeability of Rigid Porous Filters |
| ASTM D6539 | Permeability of Unsaturated Porous Materials |
| ASTM A598 | Magnetic Properties of Magnetic Amplifier Cores |
| ASTM D257 | Surface & Volume Resistivity |
| ASTM D2149 | Dielectric Constant and Dissipation Factor of Dielectrics |
| ASTM D150 | AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid |
| ASTM D149 | Dielectric Strength |
Yes. Four-point probe methods measure sheet resistance of thin films and the resistivity of wafers, and bulk methods handle conductors and insulators. We report values against your specification.
Yes. Dielectric breakdown testing determines the voltage at which an insulator fails, per thickness, and dielectric-constant testing characterizes insulation behavior across frequency.
No. We measure electrical properties and report results against the referenced method. We are not a certification body and do not issue safety listings.
MatX Lab coordinates your electrical testing through a network of accredited partner laboratories, so resistivity, dielectric, and insulation work run under one program. You work with one contact and receive one report. Methods are aligned to ASTM, IEC, and SEMI where a published method applies. MatX Lab is an analysis provider, not a standards body, and issues no certifications. Every engagement can sit under an NDA.
Test Your Materials